• Welcome to engineeringclicks.com

    • Recent Content by KevinC

    1. KevinC
      Thread

      Guide Rail coating after assembly

      All, Our Vendor made a steel structure that has bare mild steel as the outer surface, only using oil as the only mean of anti-rust protection....
      Thread by: KevinC, Aug 3, 2016, 1 replies, in forum: Surface finishes
    2. KevinC
      Post

      Maximum Bending Radius for a Beam?

      Thanks, Antonio! I"ll take a look in the feasibility in Welding the bended part.
      Post by: KevinC, Nov 25, 2014 in forum: The main mechanical design forum
    3. KevinC
      Post

      Maximum Bending Radius for a Beam?

      Hey, i don't believe this is the thread that you should discuss this matter in. Maybe you should open a new thread. You should reword your...
      Post by: KevinC, Nov 18, 2014 in forum: The main mechanical design forum
    4. KevinC
      Post

      Maximum Bending Radius for a Beam?

      Thanks, AceEngineer.
      Post by: KevinC, Nov 13, 2014 in forum: The main mechanical design forum
    5. KevinC
      Thread

      Maximum Bending Radius for a Beam?

      Dear guys: I'm not experience in bending Square Hollow Section beams. Currently I'm using a 100mmx50mmx5mm Steel beam, but planning to make a...
      Thread by: KevinC, Nov 10, 2014, 6 replies, in forum: The main mechanical design forum
    6. KevinC
      Post

      Where to buy Stainless Steel Bearings? Besides SKF.

      I‘ll take a look, thanks all !
      Post by: KevinC, Nov 1, 2014 in forum: Manufacturers of mechanical parts
    7. KevinC
      Thread

      Where to buy Stainless Steel Bearings? Besides SKF.

      Hey guys: I'm looking into purchasing stainless steel bearings (Roller and/or Ball Bearing), Spherical or not. I have a hard time finding a good...
      Thread by: KevinC, Oct 24, 2014, 12 replies, in forum: Manufacturers of mechanical parts
    8. KevinC
      Post

      vibrating stress relief and ultrasonic stress relief

      Did you find a solution? I'm actually interested in the solution.
      Post by: KevinC, Oct 24, 2014 in forum: Joining & fabrication
    9. KevinC
      Post

      best screw for joining Aluminium

      Hey, you probably are not interested in an answer now, but here is a quick answer. Strength-wise: fine pitch is better. But try to use coarse...
      Post by: KevinC, Oct 24, 2014 in forum: Joining & fabrication
    10. KevinC
      Post

      MATLAB for Mechanical Engineers

      I would be surprised if I see a Mechanical Engineer department in a company have more than 5% of engineers that would be able to use Matlab (in...
      Post by: KevinC, Oct 24, 2014 in forum: The main mechanical design forum
    11. KevinC
      Post

      Medication Delivery with your Smartphone (Looking for feedback)

      Your initial market would be small. But hope you'll do well in a long run. My suggestion: 1) At least have 5-6 catridge available, as this is a...
      Post by: KevinC, Oct 24, 2014 in forum: The main mechanical design forum
    12. KevinC
      Post

      Shaft loads static or fatigue calculation ?

      If it doesn't get to much cyclic loading (reversal loading), then just do static calculation would be good. Other wise, unless your loading...
      Post by: KevinC, Oct 24, 2014 in forum: The main mechanical design forum

    ▲

    1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies.
      Accept Learn More.
      Dismiss Notice