• Welcome to engineeringclicks.com
  • Recent Activity

    Activity stream for all registered members at EngineeringClicks.

    1. Dovile posted a new thread.

      Royal IHC is hiring a Propulsion Engineer in Kinderdijk, Netherlands

      YOUR JOB As a Propulsion Engineer, you will be responsible for engineering propulsion and drive technology. This can be done...

      Forum: Europe jobs

      Mar 24, 2017 at 10:50 AM
    2. AmandaH posted a new thread.

      What type of certifications and LOA are needed to design a ladder?

      Background: I am conducting research into design services for a 36-inch special purpose aluminum pulpit ladder. The only moving parts...

      Forum: The main mechanical design forum

      Mar 23, 2017 at 6:00 PM
    3. Erich replied to the thread Molded tube and draft.

      Yes, that is what I was talking about. With a diameter of only 6mm I would be using fewer ribs than shown. 6 to 8 max.

      Mar 23, 2017 at 3:17 PM
    4. Gilles attached a file to the thread Molded tube and draft.

      Thanks for all your answers :) The Ø are shown in the picture :). The plastic tube ID is 6mm OD is 8mm. The length of the plastic tube...

      upload_2017-3-23_8-52-48.png Mar 23, 2017 at 7:52 AM
    5. Dana replied to the thread The best software for mold tool design?.

      KeyCreator (formerly Cadkey) is popular for mold design because of its ability to import solid models from virtually any other CAD...

      Mar 22, 2017 at 8:21 PM
    6. Dana replied to the thread Molded tube and draft.

      Can you make the carbon tube with a taper that matches the plastic tube's draft? Alternatively, if you have the same draft on the ID...

      Mar 22, 2017 at 8:18 PM
    7. Erich replied to the thread Molded tube and draft.

      How long is the plastic tube? What is the diameter? You can sometimes get away with some narrow no draft ribs running the length of the...

      Mar 22, 2017 at 4:09 PM
    8. Gilles replied to the thread Molded tube and draft.

      In fact what I really need is to have the center axis of the carbon shaft and the palstic tube aligned. A deviation of .1 mm is...

      Mar 22, 2017 at 6:32 AM
    9. Neil D posted a new thread.

      Hi! I'm Neil.

      Hello everyone, I'm Neil and I'm and ME from Colorado. I was looking for a forum just so I could get some exposure to what other people...

      Forum: Pop in and say hello!

      Mar 21, 2017 at 8:53 PM
    10. Neil D has a new avatar.

      Mar 21, 2017 at 8:26 PM
    11. Neil D replied to the thread Molded tube and draft.

      Hi Gilles, I've heard of some parts molded with rapid injection molding not having a draft, but anytime anyone I've known has tried to...

      Mar 21, 2017 at 8:22 PM
    12. Gilles replied to the thread I have 2 PCBAs that are connected by a long innerly-threaded spacer.

      Might not be perfect solution but : Could you used less rigid spacer? For example palstic spacer instead of steel ? So they could be...

      Mar 21, 2017 at 3:51 PM
    13. Gilles has a new avatar.

      Mar 21, 2017 at 3:39 PM
    14. Gilles posted a new thread.

      Molded tube and draft

      Hi everyone, I have to design a plastic tube that will be glued on a carbon tube. The assembly will then be fitted into an aluminium...

      shaft.jpg

      Forum: The main mechanical design forum

      Mar 21, 2017 at 3:37 PM
    15. Mr Solve Roberg posted a new thread.

      Hi, I've just joined

      I've joined part of my quest trying to find sensible advice on which CDF software to go for. Burst type venting of high pressure...

      Forum: Pop in and say hello!

      Mar 21, 2017 at 1:27 PM
    Loading...