• Welcome to engineeringclicks.com

    • Search Results

    Search Again
    Page 1 of 4
    1. KevinC
      Thread

      Guide Rail coating after assembly

      All, Our Vendor made a steel structure that has bare mild steel as the outer surface, only using oil as the only mean of anti-rust protection....
      Thread by: KevinC, Aug 3, 2016, 1 replies, in forum: Surface finishes
    2. KevinC
      Post

      Maximum Bending Radius for a Beam?

      Thanks, Antonio! I"ll take a look in the feasibility in Welding the bended part.
      Post by: KevinC, Nov 25, 2014 in forum: The main mechanical design forum
    3. KevinC
      Post

      Maximum Bending Radius for a Beam?

      Hey, i don't believe this is the thread that you should discuss this matter in. Maybe you should open a new thread. You should reword your...
      Post by: KevinC, Nov 18, 2014 in forum: The main mechanical design forum
    4. KevinC
      Post

      Maximum Bending Radius for a Beam?

      Thanks, AceEngineer.
      Post by: KevinC, Nov 13, 2014 in forum: The main mechanical design forum
    5. KevinC
      Thread

      Maximum Bending Radius for a Beam?

      Dear guys: I'm not experience in bending Square Hollow Section beams. Currently I'm using a 100mmx50mmx5mm Steel beam, but planning to make a...
      Thread by: KevinC, Nov 10, 2014, 6 replies, in forum: The main mechanical design forum
    6. KevinC
      Post

      Where to buy Stainless Steel Bearings? Besides SKF.

      I‘ll take a look, thanks all !
      Post by: KevinC, Nov 1, 2014 in forum: Manufacturers of mechanical parts
    7. KevinC
      Thread

      Where to buy Stainless Steel Bearings? Besides SKF.

      Hey guys: I'm looking into purchasing stainless steel bearings (Roller and/or Ball Bearing), Spherical or not. I have a hard time finding a good...
      Thread by: KevinC, Oct 24, 2014, 12 replies, in forum: Manufacturers of mechanical parts
    8. KevinC
      Post

      vibrating stress relief and ultrasonic stress relief

      Did you find a solution? I'm actually interested in the solution.
      Post by: KevinC, Oct 24, 2014 in forum: Joining & fabrication
    9. KevinC
      Post

      best screw for joining Aluminium

      Hey, you probably are not interested in an answer now, but here is a quick answer. Strength-wise: fine pitch is better. But try to use coarse...
      Post by: KevinC, Oct 24, 2014 in forum: Joining & fabrication
    10. KevinC
      Post

      MATLAB for Mechanical Engineers

      I would be surprised if I see a Mechanical Engineer department in a company have more than 5% of engineers that would be able to use Matlab (in...
      Post by: KevinC, Oct 24, 2014 in forum: The main mechanical design forum
    11. KevinC
      Post

      Medication Delivery with your Smartphone (Looking for feedback)

      Your initial market would be small. But hope you'll do well in a long run. My suggestion: 1) At least have 5-6 catridge available, as this is a...
      Post by: KevinC, Oct 24, 2014 in forum: The main mechanical design forum
    12. KevinC
      Post

      Shaft loads static or fatigue calculation ?

      If it doesn't get to much cyclic loading (reversal loading), then just do static calculation would be good. Other wise, unless your loading...
      Post by: KevinC, Oct 24, 2014 in forum: The main mechanical design forum
    13. KevinC
      Post

      Is computer-based design analysis (FEM, CFD…) to be performed by an engineering desig

      Design Engineer majorly, but there are also people who will use it without being an engineer.
      Post by: KevinC, Oct 24, 2014 in forum: The main mechanical design forum
    14. KevinC
      Post

      Force calculation

      You can just use individual component and do a Free Body Diagram to solve for the shear force by the cutter. Disregard the momentum side as I...
      Post by: KevinC, Oct 23, 2014 in forum: Calculations
    15. KevinC
      Post

      How to calculate a size factor used for Endurance Limit

      Does anyone knows this questions? Sorry, I know this is a really old thread, but, anyone found the answer to this question? I know the...
      Post by: KevinC, Oct 23, 2014 in forum: Calculations
    16. KevinC
      Post

      Fasteners matching strength -washer

      It make sense to evaulate stress on the washer, any knowledge of bolt tension loss due to creep overtime?
      Post by: KevinC, Sep 10, 2014 in forum: The main mechanical design forum
    17. KevinC
      Thread

      Fasteners matching strength -washer

      Hey guys, Need some help here. Can someone share some of their experience in using harden (steel) washer? As the old saying goes: "A chain is as...
      Thread by: KevinC, Sep 5, 2014, 2 replies, in forum: The main mechanical design forum
    18. KevinC
      Post

      Gusset Mechanical Stiffener Design

      Thank you Lochnagar. You've been very helpful!
      Post by: KevinC, Jun 30, 2014 in forum: The main mechanical design forum
    19. KevinC
      Post

      Gusset Mechanical Stiffener Design

      Thanks, it helps me to get another view to what to use when it's needed. Though I still need to know how to properly apply a gusset, because it's...
      Post by: KevinC, Jun 25, 2014 in forum: The main mechanical design forum
    20. KevinC
      Post

      Gusset Mechanical Stiffener Design

      Hi, Martin. Thanks for the reply. The thing I'm working on is more onto the structural side (not really structural as in building btw). I've read...
      Post by: KevinC, Jun 25, 2014 in forum: The main mechanical design forum
    Showing results 1 to 20 of 72 Next >
    Search Again
    Page 1 of 4

    ▲

    1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies.
      Accept Learn More.
      Dismiss Notice