• Welcome to engineeringclicks.com
  • Truck Hydraulic Mobile Crane

    Discussion in 'The main mechanical design forum' started by k1mJo, Jul 25, 2012.

    1. k1mJo

      k1mJo Member

      Joined:
      Jul 2012
      Posts:
      6
      Likes Received:
      0
      Hello, i wanna design that writing the title and Do u have any project ,calculation and drawing about it,if u help me,i will be happy..

      Best Regards
       
    2.  
    3. GarethW

      GarethW Chief Clicker Staff Member

      Joined:
      Jul 2009
      Posts:
      1,424
      Likes Received:
      5
      Uh?

      Please make a bit more effort to write something a bit more specific about what you want.
       
    4. k1mJo

      k1mJo Member

      Joined:
      Jul 2012
      Posts:
      6
      Likes Received:
      0
      ok, I want to manufacture hydraulic crane for using over the truck and Do u have any project,calculations,drawing or ideas about it.

      like that HE5lu29pto4

      is it clear ?

      Thanks
      Best Regards
       
    5. PWASS

      PWASS Well-Known Member

      Joined:
      Sep 2009
      Posts:
      66
      Likes Received:
      0
      K1mJo

      You need to specify maximum working load at what reach, maximum height of lift, speed of movement and the maximum size when stowed.
       
    6. k1mJo

      k1mJo Member

      Joined:
      Jul 2012
      Posts:
      6
      Likes Received:
      0
      Thank you PWASS

      I think to design conditions that maximum height of lift is 5 tones. The size of system should be 2,5 m horizantal and 2,3 m vertical when the system is stowed.The speed of movement is gonna depend hydraulic components,i don't think that yet.
       
    7. marine&hydraulic

      marine&hydraulic Member

      Joined:
      Jun 2012
      Posts:
      7
      Likes Received:
      0
      Is this going to be for your own use or do you intend to manufacture, if the latter there will be a steep learning curve .T o answer your question on here would take a very good deal of thought and hours suggest you get more hydraulic experience before contemplating this type of work ...if the crane is for your own use I would suggest you purchase second hand/used equipment there are plentygood used cranes around at the moment
       
    8. k1mJo

      k1mJo Member

      Joined:
      Jul 2012
      Posts:
      6
      Likes Received:
      0
      Actually,we want to manufacture this kind of system and i decided to research about it.But,i don't understand .T ?
       
    9. PWASS

      PWASS Well-Known Member

      Joined:
      Sep 2009
      Posts:
      66
      Likes Received:
      0
      It's basic stuff, just pivots and levers.

      Hydraulic cylinders for the raise/lower and extend, if it has it, and a rotary actuator for the rotate.
       
    10. ChrisW

      ChrisW Well-Known Member

      Joined:
      Jun 2012
      Posts:
      68
      Likes Received:
      1
      Kimjo, I am always happy to help with advice on technical issues but there are subjects where you really shouldn't venture without the necessary knowledge and experience. Among these I include nuclear power, explosive devices, brain surgery and heavy lifting machinery!

      I have to say, if you need to ask how it's done then please make something less dangerous!
       
    11. k1mJo

      k1mJo Member

      Joined:
      Jul 2012
      Posts:
      6
      Likes Received:
      0
      Hello,ChrisW
      I agree with you,but,if we design carefully this project, i don't see any dangerous about it.So,I want to design this project and i've preapared drawings for 2 weeks.I can say it is ready.I need hydraulic calculations now,i am searching knowledge on the internet and libraries.If you help me about calculations or documents about hydraulic components,i will be happy.

      Best Regards
       
      Last edited: Jul 30, 2012

    Share This Page